General International 50-200R M1 Use and Care Manual

SETUP & OPERATION MANUALMODEL#50-200R10" LEFT TILT 2 HP TABLE SAWSPECIFICATIONSBLADE DIAMETER10” (254 MM)ARBOR DIAMETER5/8" (16 MM)ARBOR

10INSTALL THE TABLE EXTENSION WINGSAttach the table extension wings to the main tableusing 6 hex head bolts (3 per wing) and 6 lock wash-ers A. Align

4. Using the supplied 10-12 mm wrench, tighten downnuts E that secures the “L” brackets to the tableand bolts F that secures the front rail to the “L”

BE SURE THE SAW IS UNPLUGGED AND COMPLETELY DISCONNECTED FROM THE POWER SOURCE WHENEVER INSTALLINGOR REMOVING A SAW BLADE!NOTEThis saw is intended for

REMOVAL / INSTALLATIONALWAYS TURN OFF AND UNPLUG THE SAW BEFORE REMOVING / INSTALLING A RIVING KNIFE.SELECT A RIVING KNIFETwo riving knives are provid

To make satisfactory rip cuts, your fence must be aligned perfectly parallel with the saw blade.1. Slide the fence over to the right T-slot on your sa

154. Lock down the fence C.5. Make a pencil mark on the rail, in line with the point-er’s center mark, D. Then, unlock the fence and putis aside for n

CONNECTING TO A DUST COLLECTOR• There is a 4" dust outlet located on the lower left of thesaw cabinet allowing for the connection to a dust col-l

BLADE HEIGHT ADJUSTMENTThe blade height adjustment handwheel A is located onthe front of the saw, and there is a lock knob B on thehandwheel that allo

• Make sure that the arbor nut is secure and that the blade is firmly tightened snug on the arbor.• Check that the blade angle and height lock knobs a

19BEVEL RIPPINGBevel ripping is performed the same as ripping but with the saw blade set to an angle not perpendicular with thetable surface. After ch

THANK YOU for choosing this General®International model 50-200R 10" Left tilt2 HP Table Saw. This saw has been carefully tested and inspected bef

ADDING AN AUXILIARY FENCE TO THE MITER GAUGETo ensure a true 90° crosscut, especially with longer pie-ces of wood that need more support than the narr

MAINTENANCE & ADJUSTMENTSPERIODIC MAINTENANCE•Inspect/test the ON/OFF switch before each use. Do not operate the saw with a damaged switch - repla

ADJUSTING THE BEVEL ANGLE POINTERThe bevel pointer should read “0” when the blade is at 90° to the table. If not, with the blade set 90° vertical to t

RECOMMENDED OPTIONAL ACCESSORIESWe offer a large variety of products to help you increase convenience, productivity, accuracy and safety whenusing you

1a3592616061606061104a987956667756676665717052a6473941513131116129971797986313913969761107611110976791141151131171191212713013112811813213496147213A13

858483622682565453525730293024752474565525398987272890873369332683173476359036429123375051804338442249484746814580782120197776185865664386736665119121

26PARTS LIST - 50-200RPARTS N0. REF. N0. DESCRIPTION QTY50200R-01A 13300001 MAIN TABLE 150200R-02 E1210005 EXTENSION WING (LEFT) 150200R-02A E1210005

27PARTS LIST - 50-200RPARTS N0. REF. N0. DESCRIPTION QTY50200R-58 13200028 RING 150200R-59 S0050505M SET SCREW 1050200R-60 S0021025M HEX. BOLT 650200R

PARTS LIST - 50-200RPARTS N0. REF. N0. DESCRIPTION QTY50200R-116 13000004A RIVING KNIFE 150200R-117 S1500212C DUST HOSE 150200R-118 12300156B HOSE CLA

F1F2F3F3aF4F5F8F7F6F93F10F11F12F1314F15F15F15F18F19F19F20F22F21F28F14F30F32F34F35F36F14F15FENCE & RAIL ASSEMBLY – 50200R-F43F16F17F17F25F25aF25aF2

GENERAL®MFG & GENERAL®INTERNATIONAL WARRANTYAll component parts of General® MFG, General® International and Excalibur by GeneralInternational ® pr

PARTS LIST - 50200R-F43PARTS N0. REF. N0. DESCRIPTION QTY50200R-F01 11006001 FENCE BODY 150200R-F02 11006002 FENCE HEAD 150200R-F03 11006005 FENCE FRO

31PARTS LIST - 50200R-A27PARTS N0. REF. N0. DESCRIPTION QTY50200R-A01 13000004 GUARD RIVING KNIFE 150200R-A02 12700005 SUPPORT ARM 150200R-A03 1270000

IMPORTANTWhen ordering replacement parts, always give the model number, serial number of the machine andpart number. Also a brief description of each

TABLE OF CONTENTSSAFETY RULES . . . . . . . . . . . . . . . . . . . . . . .5ELECTRICAL REQUIREMENTS . . . . . . . . . . . . . .6Grounding instructions

RULES FOR SAFE OPERATIONTo help ensure safe operation, please take a moment to learn the machine’s applications and limitations, as well as poten-tial

ELECTRICAL REQUIREMENTSGROUNDING INSTRUCTIONSIn the event of an electrical malfunction or short circuit,grounding reduces the risk of electric shock t

10" LEFT TILT 2 HP TABLE SAW50-200RIDENTIFICATION OF MAIN PARTS AND COMPONENTSA- LEFT TABLE EXTENSIONB- MITER GAUGEC- SPLITTER AND BLADE GUARD AS

BASIC FUNCTIONSThis saw has been designed for cutting solid wood as well as manufactured wood materials such as plywood,woodpanelling, particleboard,

9PLACEMENT WITHIN THE SHOP /ESTABLISHING A SAFETY ZONEPLACEMENT WITHIN THE SHOPThis machine should be installed and operatedonly on a solid, flat and