General International 15-150 M1 Use and Care Manual

Steel frame and heavy duty base for greater stability.High quality conveyor belt for longer service life.Large hand wheel adjusts conveyor table heig

0VERLOAD PROTECTIONThe magnetic safety switch on this sander is equipped with an overload protection feature. To prevent an electricaloverload from da

The conveyor table can be raised or lowered , , as needed to suit the thickness of the workpiece, by rotating thecrank handle, .Note: The maximum work

Do not use this sander as a thickness planer. Never attempt to remove more than the depth of the grain of the sand-ing belt in any single pass. Too m

13OPERATIONS STEP-BY-STEPTo reduce the risk of damage to the sander or the workpiece, as well as a potential for personal injury, after initialset-up

14Disconnect machine from power source, before performing any maintenance or lubrication.Keep threaded rods, , and gears, , located at either end of

15You can also purchase them from your local tool, abrasives or sharpening supply dealer. You can find these products in most areas. However, we recom

161. Pull and hold the left spring-loaded clamp.2. Insert the left tab of the sanding belt in the slot, push ing all the way in (as

175. Push and hold the right spring-loaded clamp for-ward with your thumb. 7. Release only the first stage of the clamp, sliding your thumb dow

18Note: With the sanding belt tab properly inserted in the clamp, the clamp assembly should not pull back more than 3/4"from the slot in the drum

5. Remove the belt from the upper pulley, , and install a new belt. (See image right.)6. Lift the motor up with one hand and install the other

THANK YOU for choosing this General® International model 15-150 M1Horizontal Drum Sander. This machine has been carefully tested and inspected before

19119143434343434584a1352530252423236895471768324247141113131415163238373839282736471241904213323585132474241131A3413435413513414242471431324033474211

272728283838175124471361181121101101111111231242810113010312310710310710210914712312310310710310713028101109102105104106100124124471081084710810847471

764747474747474747474747474747474742424242262626262727272676767595954318918943189431884318995951871891851851891851891891855518318318318218318418480555

PARTS LIST - 15-150 M1PART N0. DESCRIPTION SPECIFICATION QTY15150-01 DRUM 115150-02 TWO-STEP CLAMP 115150-03 TWO-STEP CLAMP PLATE 115150-04 SPRING 1

PARTS LIST - 15-150 M1PART N0. DESCRIPTION SPECIFICATION QTY15150-58 BRONZE COLLAR 215150-59 BEVEL GEAR 415150-62 GEAR SHAFT BUSHING 215150-63 POSITIO

PARTS LIST - 15-150 M1PART N0. DESCRIPTION SPECIFICATION QTY15150-119 PC BOARD 115150-120 REGULATOR KNOB 115150-121 PC BOARD MOUNTING PLATE 1151

OFF ON IMPORTANT: When ordering replacement parts, always give the model number, serial number ofthe machine and part number. Also a brief description

1. Do not operate the sander when tired,distracted, orunder the effects of drugs, alcohol or any medica-tion that impairs reflexes or alertness.2. The

Before connecting the machine to the power source, verify that the voltage of your power supply corresponds withthe voltage specified on the I.D. name

24” HORIZONTAL DRUM SANDER15-150 M1IDENTIFICATION OF MAIN PARTS AND COMPONENTSOFF ON CRANK HANDLEDUST OUTLETCONVEYOR MOTOR START/STOP SWITCH WITH SAFE

UNPACKINGCarefully unpack and remove the unit and its components from its shipping container and check for missing ordamaged items as per the list of

7ESTABLISHING A SAFETY ZONEFor shops with frequent visitors or multiple operators, it isadvisable to establish a Safety Zone around shop machinery. A

INSTALL THE CONTROL BOX3. Tighten the bolts to secure the control box in place,with a 10 mm open end wrench. Do not plug in the power cord yet.CONNEC

9BASIC ADJUSTMENTS AND CONTROLSCONNECTING TO A POWER SOURCEOnce the assembly steps have been completed, uncoil the power cord, , and plug it into an