General International 75-155 M1 Use and Care Manual

SETUP & OPERATION MANUALVersion #1_Revision #2 - January 2015 © Copyright General International15", 17" & 20" DRILL PRESSES - V

10INSTALLING THE HEAD STOCK ON THE COLUMNASSEMBLY INSTRUCTIONSBEFORE ASSEMBLING, MAKE SURE THAT THE SWITCH IS IN THE “OFF” POSITION AND THAT THE POWER

11BEFORE ASSEMBLING, MAKE SURE THAT THE SWITCH IS IN THE “OFF” POSITION AND THAT THE POWER CORD IS UNPLUGGED. DO NOT PLUG IN OR TURN ON THE MACHINE UN

12MAKE SURE THE MACHINE HAS BEEN TURNED OFF AND UNPLUGGED FROM THE POWER SOURCE BEFORE PERFORM-ING ANY MAINTENANCE OR ADJUSTMENTS.7. Lock the table i

MAKE SURE THE MACHINE HAS BEEN TURNED OFF AND UNPLUGGED FROM THE POWER SOURCE BEFORE PERFORM-ING ANY MAINTENANCE OR ADJUSTMENTS.INSTALLING THE TABLE (

14MAKE SURE THE MACHINE HAS BEEN TURNED OFF AND UNPLUGGED FROM THE POWER SOURCE BEFORE PERFORM-ING ANY MAINTENANCE OR ADJUSTMENTS.2. Tighten the chuc

15MAKE SURE THE MACHINE HAS BEEN TURNED OFF AND UNPLUGGED FROM THE POWER SOURCE BEFORE PERFORM-ING ANY MAINTENANCE OR ADJUSTMENTS.INSTALLING THE CHUCK

16MAKE SURE THE MACHINE HAS BEEN TURNED OFF AND UNPLUGGED FROM THE POWER SOURCE BEFORE PERFORM-ING ANY MAINTENANCE OR ADJUSTMENTS.REMOVING THE CHUCKBA

17MAKE SURE THE MACHINE HAS BEEN TURNED OFF AND UNPLUGGED FROM THE POWER SOURCE BEFORE PERFORM-ING ANY MAINTENANCE OR ADJUSTMENTS.ON/OFF POWER SWITCHT

18MAKE SURE THE MACHINE HAS BEEN TURNED OFF AND UNPLUGGED FROM THE POWER SOURCE BEFORE PERFORM-ING ANY MAINTENANCE OR ADJUSTMENTS.TABLE SWING ADJUSTME

19This machine is equipped with a mechanical vari-able speed drive pulley system that allows the user to change the spindle speed while the machine is

GENERAL® INTERNATIONAL8360 Champ-d’Eau, Montreal (Quebec) Canada H1P 1Y3Telephone (514) 326-1161 • Fax (514) 326-5555 • www.general.caTHANK YOU for c

OPERATING INSTRUCTIONSCHECKLIST BEFORE STARTING• Make sure the pulley cover is closed.• Check that the chuck is installed properly.• Make sure the

21BELT REPLACEMENTMAINTENANCEInspect the belts afler every 100 hours of use. Belts that show visible signs of wear such as cracks or fraying at the edg

22MAKE SURE THE MACHINE HAS BEEN TURNED OFF AND UNPLUGGED FROM THE POWER SOURCE BEFORE PERFORM-ING ANY MAINTENANCE OR ADJUSTMENTS.Periodically lubrica

23DIAGRAM 75-155

PART # REFERENCE DESCRIPTION SPECIFICATIONS QTY75155-01 13301001A BASE 175155-02 16101002 SUPPPORT COLUMN 175155-03 SET SCREW M10 X 1

25PART # REFERENCE DESCRIPTION SPECIFICATIONS QTY75155-68 RETENTION RING 175155-69 W16205007-2 TENSIONING PULLEY SHAFT 175155-70 PIN

26DIAGRAM75-165

27PARTS LIST 75-165PART # REFERENCE DESCRIPTION SPECIFICATIONS QTY75165-01 16101001B BASE 175165-02 16201002 SUPPPORT COLUMN 175155-03

28PARTS LIST 75-165PART # REFERENCE DESCRIPTION SPECIFICATIONS QTY75155-68 RETENTION RING 175155-69 W16205007-2 TENSIONING PULLEY SHAFT

DIAGRAM75-51029

GENERAL® INTERNATIONAL WARRANTYAll component parts of General® International and Excalibur by General International® products are carefully inspected

PARTS LIST 75-510PART # REFERENCE DESCRIPTION # SPECIFICATION QTY75510-01 20101001A BASE 175510-02 20101002 SUPPPORT COLUMN 175510-03

PARTS LIST 75-510PART # REFERENCE DESCRIPTION # SPECIFICATION QTY75510-66 LOCK WASHER 175510-67 BEARING 61901 175510-68 RETENTION RIN

Follow us:8360 Champ-d’Eau, Montreal (Quebec) Canada H1P 1Y3Tel.: (514) 326-1161Fax: (514) 326-5565 - Parts & Service / (514) 326-5555 - Order Des

TABLE OF CONTENTSRules for safe operation ... 5Elect

5RULES FOR SAFE OPERATIONTo help ensure safe operation, please take a moment to learn the machine’s applications and limitations, as well as potential

ELECTRICAL REQUIREMENTS6BEFORE CONNECTING THE MACHINE TO THE POWER SOURCE, VERIFY THAT THE VOLTAGE OF YOUR POWER SUPPLY CORRESPONDS WITH THE VOLTAGE S

7IDENTIFICATION OF MAIN PARTS AND COMPONENTS A. BASEB. COLUMNC. TABLE PIVOT LOCK LEVER*D. TABLEE. FLIP-UP CHU

8UNPACKINGCarefully unpack and remove the unit and its components from the box and check for missing or damaged items as per the list of contents belo

9THIS DRILL PRESS MODEL (1) 75-155, (2) 75-165 OR (3) 75-510 IS HEAVY. DO NOT OVER-EXERT. A HOIST OR FORK-LIFT WITH STRAPS SHOULD BE USED TO LIFT THIS