SETUP & OPERATION MANUALVersion #2/Revision #1 - (S/N 32349814) May 29, 2014 © Copyright General International 13” PLANER WITH HELICAL HEADMODEL#3
This planer is equipped with a rocker style ON/OFF switch located on the front left hand side of the . To start the planer, insert the lock-out key as
DEPTH OF CUT INDICATORThe depth of cut indicator, A, will indicate how much material the cutter head is set to remove from the work-piece for a given
Max. 13”Min. 1/8”Max. 6”Min. 5”THE MAXIMUM PLANING WIDTH OF THIS UNIT IS 13”. THE MAXIMUM WORKPIECE THICKNESS OF THIS UNIT IS 6” THE MINIMUM THICKNE
1. With the planer turned off, position the workpiece on the infeed table with the flat face down and the face to be planed facing up.PLANING S
1410. The return rollers on the top of the planer can be used to pass the workpiece back to the front of the machine for repeat passes.11. Rep
15MAKE SURE THE PLANER HAS BEEN TURNED OFF AND UNPLUGGED FROM THE POWER SOURCE BEFORE PERFORMING ANY MAINTENANCE. INSPECTING/REPLACING CUTTER HEAD KNI
4. Using the supplied allen key, loosen and remove the 2 button head screw B, then remove the chip deflector.5. Insert the supplied allen key i
REPLACING THE V-BELTThe is driven by a flat ribbed belt that is located on the right-hand side of the planer facing the infeed side.17DRIVE CHAIN/GEA
RECOMMENDED OPTIONAL ACCESSORIESWe offer a large variety of products for increased convenience, productivity, accuracy and safety when using your plan
6543210151413121110987654321027444352364020323148353950494746302928262119453433218910141312112524232234428151688173738415154535517-1FRAME ASSEMBLY19
THANK YOU for choosing this General® International model 30-005HC M1 13” Planer with Helical . This planer has been carefully tested and inspected be
NMAIN ASSEMBLY20
21PARTS LIST30-005HC M1PART N0. REF. N0. DESCRIPTION SPECIFICATION QTY1 30005-01 HANDLE ASSEMBLY 12 30005-02 CAP SCREW M5xP0.8x20L 18 3
22PARTS LIST30-005HC M1PART N0. REF. N0. DESCRIPTION SPECIFICATION QTY61 30005-61 BEARING SEAT 162 30005-62 BEARING 6203ZZ 263 30005-63
PARTS LIST30-005HC M1PART N0. REF. N0. DESCRIPTION SPECIFICATION QTY161 30005-161 MOTOR FAN COVER 1162 30005-162 WAVE WASHER 1163 300
IMPORTANTWhen ordering replacement parts, always give the model number, serial number of the machine and part number. Also a brief description of each
GENERAL®INTERNATIONAL WARRANTYAll component parts of General® International and Excalibur by General International® products are carefully inspected d
TABLE OF CONTENTSRules for safe operation... 5Electrical requirements ... 6Grounding instr
1. Do not operate this planer when tired, distracted, or under the effects of drugs, alcohol or any medication that impairs reflexes or alertne
6 ELECTRICAL REQUIREMENTS GROUNDING INSTRUCTIONSIn the event of an electrical malfunction or short circuit, grounding reduces the risk of electri
IDENTIFICATION OF MAIN PARTS AND COMPONENTS IN-FEED TABLE STOCK THICKNESS SCALE HEIGHT ADJUSTMENT HANDLE RETURN ROLLERS CIRCUIT BREAKER ON/OFF SWITC
Carefully unpack and remove the planer and its compo-nents from the box and check for damaged or missing items as per the list of contents below.NOTE:
ATTACH THE DEPTH OF CUT ADJUSTMENT HANDLEATTACH THE DUST CHUTEAttach the adjustment handle on top of the machine as shown, using the supplied allen ke
Comments to this Manuals