FEATURESThe table rides on 14 sealed, steel ballbearing rollers and is supported by archi-tectural grade heavy-duty steel tubing.Easy to adjust, extru
ATTACH THE REAR INNER LEG MOUNT TO THE INNER GUIDE RAIL2. Attach the rear leg mount to the inner rail using 2 hex bolts and 2 washers ,aligning the le
INSTALL THE REAR CROSS BRACE3. Attach the saw mounting bracket to the rear cross brace as shown, using the same hardware,in the same assembly order
8. Attach the outer rail to the leg mounts (with the wide polished surface closest to the table saw) as shown, using 4 hex bolts and washers from ha
5. To set and maintain even spacing between the inner rail and the sliding table, insert wood or card-board shims (1/8”- 3/16” thick) between the inne
INSTALL THE ANGLE ADJUSTMENT RAIL1. Attach the angle adjustment rail to the outside edge of the sliding table by sliding the t-nutsinto the T-slot in
4. Thread a ratchet lever onto the fence pivot brackets at each end of the table.3. Thread a t-nut on to one of the ratchet levers .Then slide the
8. Install the two thumbscrews into the holes in the front face of the cross cut fence.Note: The thumbscrew is used to lock the fence extensionpost i
VERY IMPORTANT!THE FOLLOWING ADJUSTMENTS WILL PROVIDE ACCURACY ONLY IF YOUR SAW TABLE IS LEVELED WITH THEFLOOR. USE SHIMS (OR LEVELING FEET IF IT HAS
SETTING THE SLIDING TABLE TRACKINGThe sliding table must be set to run parallel to the blade(and not the mitre slot ) .Verify and, if needed, set the
4. To adjust the outer rail, loosen the 2 bolts on the front and center outer leg bracket .5. Manually adjust either the front or rear end of the out
THANK YOUfor choosing this Excalibur by General®International model 50-SLT60P Sliding Table. This sliding table has been carefully tested and inspecte
3. Loosen the miter clamp and adjust the cross cut fence to the perpendicular face of your machi-nists square . Then secure the cross cut fence in
1. If installed, remove the extension from the cross-cut fence.2. Loosen the miter clamp and slide the fence off of the angle adjustment rail.3. Lift
Once the cross cut fence has been reversed to rear posi-tion, verify and, if needed, adjust the alignment of thecross cut fence for rear mounted posit
To set the sliding scale and permit accurate measurements using the flip stop:3. Secure the sliding scale by tightening the locking bolt.1. Set the fe
VERIFY ALL FOLLOWING CHECK POINTS BEFORE TURNING ON THE SAW. FAILURE TO COMPLY CAN RESULT IN SERIOUS INJURIES.CHECK POINTS6. Turn on the saw and proce
DO NOT USE RIP FENCE AS A GUIDE OR WORKPIECE STOP WHEN OPERATING THE SLIDING TABLE. TO AVOID POTENTIAL OFWORKPIECE BINDING WHICH WILL CAUSE KICKBACK,
The two slots in the quick mount bracket are for reposi-tioning the cut capacities of this unit.For maximum stability, use all four socket head cap s
RECOMMENDED OPTIONAL ACCESSORIESHere are some of the optional accessories available from your local General International dealer.For more information
51525354515253535152545451525371719371719240927840747571937960910731817101446485555567171717171577171717171716971717171 717171717169696971406810010168
M10917101318311986913810101618102122102311121062118171310261718101991718109625122625513108961961011477221023715911209799797181713152490581918101710181
GENERAL®MFG & GENERAL®INTERNATIONAL WARRANTYAll component parts of General® MFG, General® International and Excalibur by GeneralInternational ® pr
M43271339328636503337386416365666626163872844292967646389495808932918535838431102823388303442CROSS CUT FENCE30
31PARTS LIST 50-SLT60PREF. N0. PART N0. DESCRIPTION SPECIFICATION QTY1 50SLT60-01 PLUG 12 50SLT60-02 RETURN HANDLE 13 50SLT60-03 SLIDING ANGLE INDIC
32PARTS LIST 50-SLT60PREF. N0. PART N0. DESCRIPTION SPECIFICATION QTY52 50SLT60-52 CAP NUT M8 X 1.25P 1253 50SLT60-53 CARRIAGE BOLT 5/8 X 1.25P X
NOTES33
IMPORTANTWhen ordering replacement parts, always give the model number, serial number of the machine andpart number. Also a brief description of each
TABLE OF CONTENTSSAFETY RULES . . . . . . . . . . . . . . . . . . . . . . .5IDENTIFICATION OF MAIN PARTS ANDCOMPONENTS . . . . . . . . . . . . . . .
1. Do not operate the saw when tired, distracted, or under the effects of drugs, alcohol or any medica-tion that impairs reflexes or alertness.2. The
SLIDING TABLE50-SLT60PIDENTIFICATION OF MAIN PARTS AND COMPONENTS RAIL & BRACE ASSEMBLY TABLE & CROSS CUT FENCE ASSEMBLY CROSS CUT FENCEMITER
UNPACKINGCarefully unpack and remove the unit and its compo-nents from the box and check for missing or damageditems as per the list of contents below
8VERY IMPORTANT!BEFORE PROCEEDING WITH THE ASSEMBLY STEPS MAKE SURE THE SAW TABLE IS LEVELED WITH THEFLOOR, PLACING A LEVEL ON THE TABLE. USE SHIMS (O
2. Fit a support leg into the four brackets as shown then tighten with two hex bolts and flat washers.Tip: Select the second hole from the top of the
Comments to this Manuals